ER347 TIG / GTAW Filler Metal: Filler Metal Finder Notes

ER347 TIG / GTAW filler metal is a stabilized stainless filler used in TIG welding support conversations for 321 and 347 stainless applications. Treat the filler metal listing as a selection starting point, not as procedure approval. Before ordering rod or starting a weld, verify the WPS, code requirements, base metal grade, service conditions, and the manufacturer data sheet.

The most useful approach is simple: confirm the joint details first, then confirm the filler choice. If the base metal, service temperature, or corrosion environment is not fully known, do not assume ER347 is the correct answer. Use the product page and the filler metal finder page to narrow the selection, then validate against the actual job requirements.

Key Takeaways

• ER347 is a stabilized stainless filler metal used with TIG / GTAW processes.
• The listed application focus is 321 and 347 stabilized stainless, but final selection depends on the WPS and base metal.
• Do not treat the filler metal page as a procedure approval. It is a starting point only.
• Verify weld joint requirements, corrosion exposure, and post-weld service conditions before use.
• If any technical detail is uncertain, mark it Unknown (Verify) and check the data sheet.

What ER347 TIG / GTAW Filler Metal Is Used For

ER347 is commonly considered when the job involves stabilized stainless steel and TIG / GTAW welding. Stabilized stainless filler selection matters because the filler must match the weld metal performance expected by the design, the governing code, and the service environment. That means the base metal grade and service conditions are part of the selection process, not just the alloy number on the spool or tube.

On the Weld Support Parts filler metal page, the listing should be read as a support reference. It can help a buyer or welder start the search, but it does not replace the procedure specification. If the WPS calls for a different filler metal, follow the WPS.

Check / Inspect / Verify Before Welding

• Check the WPS for the specified filler classification. If the WPS is missing or unclear, stop and verify it before setup.
• Inspect the base metal stamping, mill certs, or job documentation to confirm whether the material is 321, 347, or another stainless grade.
• Verify the service environment. Heat, corrosion exposure, and process contamination can change the filler choice.
• Check the wire size or rod diameter required by the job. Common sizes may be listed on the product page, but if a size is not confirmed there, mark it Unknown (Verify).
• Inspect storage and handling conditions. Stainless filler should be kept clean and protected from contamination.
• Verify the manufacturer data sheet for AWS classification, recommended use, and any limitations.

Troubleshooting Support Notes

If the filler classification does not match the WPS: stop and confirm whether the job allows an alternate filler. Do not substitute based on appearance or assumption.

If the base metal grade is uncertain: do not guess between 321, 347, or another stainless grade. Check drawings, PMI results, material certs, or customer documentation.

If weld quality changes during the job: inspect preparation, shielding gas coverage, cleanliness, and heat input control. ER347 cannot correct process problems caused by contamination or poor setup.

If the service condition is high-temperature or corrosive: verify whether stabilized stainless filler is required and whether the governing procedure has additional restrictions. When in doubt, mark the service condition Unknown (Verify) until confirmed by engineering or the WPS.

Filler Metal Finder Section

Use the Weld Support Parts filler metal finder as a selection aid when you are narrowing down stainless TIG filler options. It is a starting point for product identification, not a guarantee of procedure approval.

Open the filler metal finder

The finder is useful when you know the process is TIG / GTAW and you are comparing classifications for stainless work. It should still be checked against the actual WPS, code, and base metal. If the job requires a different filler metal, the finder result does not override the procedure.

Product Page Support Notes

For the ER347 TIG / GTAW filler metal listing itself, use the product page as the primary reference on the store side and compare it with the filler metal finder result. If a detail is not clearly shown, treat it as Unknown (Verify) rather than filling in the gap from memory.

View ER347 TIG / GTAW filler metal

Before purchase, verify the following:

• AWS classification listed on the product page and data sheet.
• Actual rod or filler size needed for the job. If not shown, Unknown (Verify).
• Whether the application is for 321 or 347 stainless, or another approved use under the WPS.
• Any code, customer, or plant restrictions on filler selection.

Safety Notes

• Do not weld stainless without confirming the correct filler and shielding plan for the job.
• Keep filler metal clean. Surface contamination can cause weld defects and corrosion issues.
• Follow site safety rules for heat, arc flash, fume exposure, and hot work permits.
• If the job involves unknown alloy identity, stop and verify before proceeding.
• When technical data is not confirmed by the product page or data sheet, use Unknown (Verify).

FAQ

Is ER347 TIG / GTAW filler metal automatically correct for 321 stainless?
No. It may be used in stabilized stainless applications, but the WPS and base metal confirmation control the final selection.

Can I use the filler metal finder as a welding approval tool?
No. The finder is a selection starting point only. Verify the procedure, code requirements, and manufacturer data sheet before welding.

What should I do if the base metal grade is not confirmed?
Stop and verify the material grade through documentation, PMI, or engineering review. Do not assume the alloy.

What if the product page does not show a detail I need?
Treat it as Unknown (Verify) and check the data sheet or contact the responsible welding support team before ordering.

Sources Checked

• Weld Support Parts product page: ER347 TIG / GTAW Filler Metal
• Weld Support Parts filler metal finder: Filler Metal Finder
• Provided source notes for ER347 TIG / GTAW filler metal selection support

Selection reminder: ER347 TIG / GTAW filler metal should be selected from verified job data, not from assumption. Confirm the WPS, code requirements, base metal grade, service conditions, and manufacturer data sheet before ordering or welding.

Disclosure: As an Amazon Associate, Weld Support Parts may earn from qualifying purchases.